RaspberryPi:DebuggingConnectivity - Revision history

CRNKEE002: /* Ubuntu */

2020-09-15T07:51:41Z

Ubuntu

CRNKEE002: /* Ubuntu */

2020-09-14T10:01:06Z

Ubuntu

CRNKEE002: /* Ubuntu */

2020-09-14T10:00:51Z

Ubuntu

CRNKEE002: /* SSH'ing Into the Pi 0/0W */

2020-09-10T13:37:44Z

SSH'ing Into the Pi 0/0W

CRNKEE002: /* Windows */

2020-09-10T09:06:04Z

Windows

CRNKEE002 at 09:03, 10 September 2020

2020-09-10T09:03:03Z

CRNKEE002 at 09:40, 6 February 2020

2020-02-06T09:40:47Z

CRNKEE002 at 09:38, 6 February 2020

2020-02-06T09:38:26Z

CRNKEE002: Created page with "= Debugging Connections = This section is a work in progress. As more common issues are reported by students, this section will be expanded. It's important to note that most..."

2020-02-06T09:37:46Z

Created page with "= Debugging Connections = This section is a work in progress. As more common issues are reported by students, this section will be expanded. It's important to note that most..."

New page

= Debugging Connections =

This section is a work in progress. As more common issues are reported by students, this section will be expanded. It's important to note that most connectivity problems come down to an incorrectly configured file, where you may have missed a space, or misspelled something.

= Note for Windows Users =

If you are having trouble accessing the internet from your Pi using the Ethernet Passthrough technique, it’s likely the Windows bridge needs a reset. Change the IPv4 address of your Ethernet port to “Obtain an IP address automatically”, then on your WiFi connection, disable sharing, click okay, and then re-enable sharing. Go back to the IP configuration of your Ethernet post, and double check the IP to see if it’s been assigned 192.168.137.1. If not, you will need to change it using the “Advanced settings” button.

= WiFi =

See if you can see wireless networks.

<pre>$ iwlist wlan0 scan</pre>
If you cannot connect via WiFi, enter into a shell on the Pi and run:

<pre>$ journalctl -u wpa_supplicant | grep wlan0
$ journalctl -u dhcpcd.service | grep wlan0</pre>
This will output the log files and notify you of any incorrect configurations in wpa_supplicant.

The following command will force the interface to be up (if it can be):

<pre>sudo ifconfig wlan0 up</pre>
If all else fails, reboot and try again. Some services can be restarted without restarting the Pi, for example:

<pre>sudo systemctl restart dhcpcd</pre>
Test wpa_supplicant config by killing the process, and running it in debug mode:

<pre>sudo killall wpa_supplicant
sudo /sbin/wpa_supplicant -d -c/etc/wpa_supplicant/wpa_supplicant.conf -Dnl80211,wext -iwlan0</pre>

= "Failure resolving URLs" or "unknown host" =

If you try to ping a website from the Pi and it fails, but pinging a IP such as 8.8.8.8 works as expected, it is likely an issue with DNS configuration. Open the resolv.conf file:

<pre>$ sudo nano /etc/resolv.conf</pre>
And edit it to read the following:

<pre>nameserver 8.8.8.8
nameserver 192.168.137.1</pre>
8.8.8.8 is the IP of Google’s DNS server. A DNS (Domain Name Service) server is responsible for converting human-readable addressed (for example google.co.za) to something the network architecture can understand (172.217.170.67, in this example).

If you still get this error, try running the following command:

<pre>$ sudo route add default gw 192.168.137.1</pre>
Where the IP supplied is the IP of the computer or router you are connected to.

@@ Line 85: / Line 85: @@
 Some Ubuntu systems are unable to perform the IP lookup based on the hostname.
 Follow the instructions [https://askubuntu.com/questions/992388/ubuntu-avahi-daemon-cannot-find-raspberrypi-local/1010785#1010785 here] to connect.
 Once you've connected, it's suggest you connect to a wifi network to be able to SSH in using "pi@raspberrypi.local", or set a static IP on the USB port and use the same subnet on the network created on the PC when you plug in the Pi.

← Older revision		Revision as of 10:01, 14 September 2020
Line 86:		Line 86:
	Follow the instructions [https://askubuntu.com/questions/992388/ubuntu-avahi-daemon-cannot-find-raspberrypi-local/1010785#1010785 here] to connect.		Follow the instructions [https://askubuntu.com/questions/992388/ubuntu-avahi-daemon-cannot-find-raspberrypi-local/1010785#1010785 here] to connect.

−	Once you've connected, it's suggest you connect to a wifi network to be able to SSH in using "raspberrypi.local", or set a static IP on the USB port and use the same subnet on the network created on the PC when you plug in the Pi.	+	Once you've connected, it's suggest you connect to a wifi network to be able to SSH in using "pi@raspberrypi.local", or set a static IP on the USB port and use the same subnet on the network created on the PC when you plug in the Pi.

← Older revision		Revision as of 10:00, 14 September 2020
Line 85:		Line 85:
	Some Ubuntu systems are unable to perform the IP lookup based on the hostname.		Some Ubuntu systems are unable to perform the IP lookup based on the hostname.
	Follow the instructions [https://askubuntu.com/questions/992388/ubuntu-avahi-daemon-cannot-find-raspberrypi-local/1010785#1010785 here] to connect.		Follow the instructions [https://askubuntu.com/questions/992388/ubuntu-avahi-daemon-cannot-find-raspberrypi-local/1010785#1010785 here] to connect.
		+
		+	Once you've connected, it's suggest you connect to a wifi network to be able to SSH in using "raspberrypi.local", or set a static IP on the USB port and use the same subnet on the network created on the PC when you plug in the Pi.

@@ Line 64: / Line 64: @@
 <ol>
 <li> Open up device manager by pressing the Windows key and X and selecting "Device Manager" from the drop down</li>
-<li>If you have no other USB to Ethernet Gadgets plugged in, and you see this, it means your Pi is connected correctly and you need to double check you've installed Bonjour and are connecting to the correct hostname. PICTURE
+<li>If you have no other USB to Ethernet Gadgets plugged in, and you see this, it means your Pi is connected correctly and you need to double check you've installed Bonjour and are connecting to the correct hostname.
 </li>
 <li> If under "Universal Serial Bus controllers" you see something like "Unknown USB Device (Device Descriptor Failed)", it means the driver is not installed. <br>
 [[File:RNDISDriverNotInstalled.png|none|left]]
@@ Line 81: / Line 83: @@
 == Ubuntu ==

@@ Line 66: / Line 66: @@
 <li>If you have no other USB to Ethernet Gadgets plugged in, and you see this, it means your Pi is connected correctly and you need to double check you've installed Bonjour and are connecting to the correct hostname. PICTURE
 </li>
-<li> If you see this, it means the driver is not installed. <br>
+<li> If under "Universal Serial Bus controllers" you see something like "Unknown USB Device (Device Descriptor Failed)", it means the driver is not installed. <br>
 [[File:RNDISDriverNotInstalled.png|none|left]]
 To install the driver, you need to do the following:
@@ Line 79: / Line 79: @@
 </ol>
 == Ubuntu ==

← Older revision		Revision as of 09:03, 10 September 2020
Line 58:		Line 58:
	<pre>$ sudo route add default gw 192.168.137.1</pre>		<pre>$ sudo route add default gw 192.168.137.1</pre>
	Where the IP supplied is the IP of the computer or router you are connected to.		Where the IP supplied is the IP of the computer or router you are connected to.
		+
		+	= SSH'ing Into the Pi 0/0W =
		+	This section assumes you've correctly modified the SD card contents using the correct editor, and are using the correct USB port on the Pi.
		+	== Windows ==
		+	<ol>
		+	<li> Open up device manager by pressing the Windows key and X and selecting "Device Manager" from the drop down</li>
		+	<li>If you have no other USB to Ethernet Gadgets plugged in, and you see this, it means your Pi is connected correctly and you need to double check you've installed Bonjour and are connecting to the correct hostname. PICTURE
		+	</li>
		+	<li> If you see this, it means the driver is not installed. <br>
		+	[[File:RNDISDriverNotInstalled.png\|none\|left]]
		+	To install the driver, you need to do the following:
		+	<ol>
		+	<li>Right click on the "Unknown USB Device" and uninstall the driver.</li>
		+	<li>Unplug the Pi from your computer</li>
		+	<li>Download the RNDIS drivers here: [[Media:Mod-duo-rndis.zip\|Windows 10 RNDIS Drivers]] </li>
		+	<li>Extract the contents</li>
		+	<li>Right click on "RNDIS.inf" and select "install"</li>
		+	<li> Plug in the Raspberry Pi again, it should be picked up as a USB Ethernet Device under "Network Adapters"</li>
		+	</ol>
		+
		+	</ol>
		+	== Ubuntu ==

← Older revision		Revision as of 09:40, 6 February 2020
Line 7:		Line 7:

	If you are having trouble accessing the internet from your Pi using the Ethernet Passthrough technique, it’s likely the Windows bridge needs a reset. Change the IPv4 address of your Ethernet port to “Obtain an IP address automatically”, then on your WiFi connection, disable sharing, click okay, and then re-enable sharing. Go back to the IP configuration of your Ethernet post, and double check the IP to see if it’s been assigned 192.168.137.1. If not, you will need to change it using the “Advanced settings” button.		If you are having trouble accessing the internet from your Pi using the Ethernet Passthrough technique, it’s likely the Windows bridge needs a reset. Change the IPv4 address of your Ethernet port to “Obtain an IP address automatically”, then on your WiFi connection, disable sharing, click okay, and then re-enable sharing. Go back to the IP configuration of your Ethernet post, and double check the IP to see if it’s been assigned 192.168.137.1. If not, you will need to change it using the “Advanced settings” button.
		+
		+	= Ping =
		+	''Ping'' sends a packet to a particular host (in this case the Pi), and measures the time taken for a response from that host.
		+
		+	To use the ping command, open a command prompt window or terminal and type the following:
		+
		+	<pre>$ ping 192.168.137.15</pre>
		+	If that host is unreachable (the Pi hasn’t booted yet or is incorrectly configured), a message will show that the host is unreachable. If everything was correctly configured, you should get
		+
		+	<pre>Reply from 192.168.137.15: bytes=32 time<1ns TTL=64</pre>
		+	This means your Pi and computer are both correctly configured.
		+
		+	'''NB:''' Don’t be surprised if you can’t ping a Windows machine from your Pi. Windows blocks the specific type of packet required for a ping in the firewall.

	= WiFi =		= WiFi =

← Older revision		Revision as of 09:38, 6 February 2020
Line 1:		Line 1:
		+	[[Category:RaspberryPi]]
	= Debugging Connections =		= Debugging Connections =